Notifier UZC-256 Universal Zone Coder Software Release 2 0

UZC 256 Zone Coder Release 2.0 UZC 256 Universal Zone Coder enables the Notifier intel fire alam control panels FACPs network control annun NCAs and compatible legacy systems to provide non interfering successive zone coded outputs Up to separate codes may be programmed to operate on the coded outputs Each output is used to code or pulse up 3 Amps of Notification Appliance power Coded output from the UZC 256 can be fed to multiple out circuits Up to 256 individually programmed codes Three 3 Amp outputs Programmable rounds of code 1 to 99 rounds Up to four digits per round Up to 15 pulses per digit of code Optional general alarm Programmable code and round s delay Programmable pulse and digit pause times Connects and communicates over panel EIA 485 interface Programmable for California code Weight 1.75 lbs 2.0 Features Secondary UZC use counting alarm operation activates relays after specified number of alarms Programmable address EIA 485 range 1 32 No code counting selection for non fire points UZC 256 provides three outputs that supply unique coded to certain output circuits depending on the alarm condition This can be useful when employing coded in floor above floor below applications or to provide numbers of rounds for bell circuits and strobe or lamp Due to the nature of coded outputs the UZC 256 is not with notification devices which do not produce a steady non periodic sound Periodic appliances that produce their own such as some codes available with electronic sounders will be compatible with the UZC 256 Refer to the UZC 256 Instal Manual for a list of compatible panels Operation UZC 256 provides three coded output relays each rated three amps at 30 VDC These relays are controlled by a program and can be set to respond to general conditions with the fire alarm system UZC 256 and the CPU use the EIA 485 circuit for commu When installed the zone coder has a programmable on the EIA 485 interface of points to zone codes within the UZC 25 is pro in the NFS2 3030 NFS2 640 NFS 320 and NCA see programming manuals for details D 140 Control Systems Universal Zone Coder Specifications current 35 mA current 55 mA the system including components and peripheral in the following nominal environment 60 to 80 15.6 to 26.7 humidity 40 to 60 non condensing Listings and Approvals some cases certain modules or applications may not be by certain approval agencies or listing may be in pro Consult factory for latest listing status UL Listed S624 ULC Listed CS118 CS733 CBP696 MEA 289 91 E Vol III 290 91 E Vol III 291 91 E Vol II 345 02 E 232 06 E CSFM 7165 0028 141 7165 0028 144 7165 0028 157 7165 0028 214 NFS 640 7165 0028 224 7170 0028 153 7170 0028 154 7170 7170 0028 216 NFS 640 7170 0028 223 NFS2 3030 7165 0028 243 NFS2 640 FDNY COA Lloyd Register 93 60 40 E2 AM2020 AFP1010 FM Approved 11 17 09 Page 1 of 2 Programming the UZC 256 is accomplished through the serial port of an IBM PC The Software Interface UZC SI the user to select from a variety of code options see software coding The UZC requires power from the control panel to the programmed code Alternately it may be powered with a 9 VDC power transformer which is included the UZC Hardware Interface UZC HI Compatible PC Line Information Universal Zone Coder power cable and mounting UZC 256 Software Interface Version 2.0 must be with UZC 256 EPROM 73712 or greater Provides the to program the UZC Includes programming instruc and programming software UZC 256 Hardware Interface Includes null modem 9 pin to 25 pin adapter and a 9 VDC power transformer Backbox for housing the UZC for applications where UZC will not fit in the panel enclosure Black casing same as BB UZC but with a red casing Power Harness Order when mounting the UZC 256 in BB 17 System 500 applications Software Coding code up to 256 may be up to four digits long and each can be from 0 to 15 pulses User selectable times and may also be programmed Time The period from when the alarm is received at control panel and the code begins Value can be 0 to 99 of Rounds The number of times the code will Value can be 1 to 99 Time The period each pulse will sound Value can be to 1 second in 1 100th of a second increments Pause The pause between digits of the code Value be 0 to 10 seconds in 1 10th of a second increments Pause The pause between pulses of the digit Value be 0 to 1 second in 1 100th of a second increments Pause The pause between the round s of the code can be 0 to 10 seconds in 1 10th of a second incre Alarm Provides the UZC with the capability to turn selected Indicating Circuits general alarm after complet its code See the appropriate installation manual for infor on the Alarm feature is a trademark of Honeywell International Inc IBM is a trademark of IBM Corporation by Honeywell International Inc All rights reserved Unauthorized use this document is strictly prohibited document is not intended to be used for installation purposes We try to keep our product information up to date and accurate cannot cover all specific applications or anticipate all requirements specifications are subject to change without notice more information contact Notifier Phone 203 484 7161 FAX 203 484 7118 in the U S A 2 of 2 dn 3404 b 11 17 09