Potter HS-24-WP Series Weatherproof 75 Candela Wall Mount Horn Strobe

Features Fixed 75cd strobe Includes the WPBB surface mount standard or WPLPBB Low Profile enclosure WPBB LP made of clear Lexan provides maximum visibility and allowing full 75cd output Super Slide Bracket Ease of supervision testing Checkmate Instant voltage verification Synchronize strobe and or horn with AVSM module Switch selection for high low dBA Switch for chime whoop mechanical and 2400Hz tone Input terminals accept 18 to 12 AWG Switch for continuous or temporal 3 tone not available on whoop Tamperproof re entrant grill 5 year warranty Version S3247 S HS WP Series Outdoor Signals are wall mount low profile and horn strobes that offer dependable audible and visual for warning and emergency notification in outdoor locations Listings ANSI UL 464 and 1638 with American with Disabilities Act ADA with IBC IFC IRC S HS WP Series Outdoor Signals are 24VDC strobes and horn equipped with a fixed 75 candela strobe series of outdoor signals are available in two different versions standard version includes a surface mount back box WPBB to directly on a wall The Low Profile LP versions includes a profile back box WPLPBB designed to be installed on a flush electrical box The weatherproof enclosure is made of Lexan which provides maximum visibility and reliability for visible signaling allowing full 75cd output S HS WP series strobe has a minimal operating current and a flash rate of 1Hz regardless of input voltage The strobe is using Gentex sync protocol or the AVSM Sync Module S HS WP Series is equipped with a universal 4 mounting bracket incorporates the popular Super Slide feature that allows the to easily pre wire the system and test for supervision The also features a locking mechanism that secures the signal to bracket without showing any screws and the Checkmate Instant Verification Feature which allows the installer to check the drop current draw and match against the blue print Specifications Voltage 24VDC 16 33VDC 150 35 66 Version 5.75 H x 4.75 W x 3.25 D 5.75 H x 4.75 W x 4.18 Connections accept 18 12 AWG Weight Version Single gang double gang or square back box Version Surface mount back box lbs PAGE 1 OF 4 SeriesOutdoor Strobes and Horn Strobes8830057 REV B 3 15Potter Electric Signal Company LLC St Louis MO Tech Support 866 956 1211 Customer Service 866 572 3005 www pottersignal comfirealarmresources com 75 Candela Outdoor Strobe Standard or LP Enclosure Number 4890057 Color Enclosure Profile Profile Profile Profile Designations Wall Mount Red Face Plate White Face Plate Plain Note Plain units are non returnable Low Profile WPLPBB Enclosure Current Ratings cd mA mA VDC Max For unfiltered FWR ratings see installation manual Series 75 Candela Outdoor Horn Strobe Standard or LP Enclosure Color dBA at 10 per ANSI UL 464 Anechoic Room dBA at 10 WP Enclosure Number 4890067 Decibel and Current Ratings at 10 UL 464 at 10 UL 464 24VDC Operating at High mA Setting 3 2400Hz 3 Mechanical 3 Chime 2400Hz Mechanical Chime the horn in this mode at this voltage will result in not meeting minimum ANSI UL 464 reverberant sound level required for public fire protection service These settings are acceptable only for mode fire alarm use Use the high dBA setting for public mode not applicable when using the chime tone The chime tone always private mode Profile Profile Profile Profile PAGE 2 OF 4 8830057 REV B 3 15Potter Electric Signal Company LLC St Louis MO Tech Support 866 956 1211 Customer Service 866 572 3005 www pottersignal comS HS WP SeriesOutdoor Strobes and Horn Strobesfirealarmresources com Switch Locations Temporal 3 Continuous Temporal 3 Continuous Temporal 3 Continuous Position Positions 1 and 2 in the OFF position to select horn and strobe power inputs Position 6 ON HIGH dBA Position 6 OFF LOW dBA Slide Mounting Bracket the installer to pre wire the system test for system remove the signal head until occupancy switch signals without changing mounting brackets and has edge connector for snap in place installation Outdoor Enclosure Slide Mounting Plate to WPBB Outdoor Enclosure Slide Mounting Plate to WLPBB Outdoor Enclosure Instant Voltage is often necessary to confirm the voltage along the line of devices The access are provided in the back of the block to allow the voltage to measured directly without removing device Typically this would be done the end of the line to confirm design Most measurements will be taken the S and S locations although is provided to other locations Care should be taken to not the test probes PAGE 3 OF 4 SeriesOutdoor Strobes and Horn Strobes8830057 REV B 3 15Potter Electric Signal Company LLC St Louis MO Tech Support 866 956 1211 Customer Service 866 572 3005 www pottersignal comfirealarmresources com Diagrams All strobes are designed to flash as specified with continuous applied voltage Strobes should not be used on coded or pulsing signaling circuits use of the AVSM control module or Gentex synchronization protocol is permitted to synchronize the strobe horn and or mute the horn SYNCHRONIZATION WIRING INFORMATION REFERENCE AVSM CONTROL MODULE DATA SHEET 8830050 AND OR CONTROL MODULE MANUAL FOR SYNCHRONIZATION MODULE WIRING DIAGRAMS AVSM CONTROL MODULE SHEET AND MANUAL CAN BE OBTAINED AT http pottersignal com OR CALL POTTER ELECTRIC AT 1 800 325 3936 and Engineering Specifications audible and or visible signal shall be Potter S HS WP Outdoor Series or approved equal and shall be listed by Underwriters Laboratories Inc per ANSI 1638 and or ANSI UL 464 notification appliance combination audible visible shall produce a peak sound output of 100dBA or greater at as measured in an anechoic chamber signaling appliance shall also have the capability to silence the audible signal while leaving the visible signal energized with the use of a single pair power wires Additionally the user shall be able to select either continuous or temporal tone output with the temporal signal having the ability to be audible visible and visible signaling appliance shall also maintain a minimum flash rate of 1Hz or up to 2 Hz regardless of power input voltage appliance shall have an operating current of 112mA or less for the 75Cd strobe circuit The appliance shall also be capable of meeting the candela of the ADA 75cd appliance shall be polarized to allow for electrical supervision of the system wiring