Potter PSN Series Dip Switch Programming

PSN Series Power Supplies Dip Switch Programming Quick Start PSN 106 PSN 64 power before servicing or changing DIP switch selections Switch Input Trigger Type Trigger Type programming option selects the behavior of trigger inputs as follows Trigger Debounce Slow Trigger Triggers Amseco Wheelock System Sensor 1 Dip Switch Input Trigger Settings input is sampled at a high rate Used for simple DC triggers as well as pass mode a non standard trigger signal to be used for activation The slower response allows outputs to remain active when the trigger signal is changing This trigger will operate a pulsing input is provided when a supported synchronized input trigger signal is provided 1 Example of Dip Switch S7 Input Trigger Type Settings position ON 2 Trigger Type Normal Slow Debounce 1 Trigger Type OFF OFF Normal OFF OFF Slow Debounce ON OFF Amseco Sync ON OFF Gentex Sync OFF ON System Sensor Sync OFF ON Wheelock Sync 3590 15A page 1 OF 5 Electric Signal Company LLC St Louis MO Phone 800 325 3936 www pottersignal com8870042 REv A 6 16PSN Series Dip Switch Programmingfirealarmresources com Switch Setting Options A B Selection Holder AC Dropout Delay Power Output is Door Holder Memory Enabled 2 Dip Switch Settings Each example If the circuit pair 1 2 is programmed for Class a operation then only the NaC option dip switch for circuit 1 will be used response to a low aC condition in order to minimize standby current To minimize conditions a selectable aC dropout delay is provided doorholder dropout on AC Loss is selected door holder power will drop out in to an alarm condition only Specifies selected the DC power will drop out in response to an alarm condition and optionally a aC condition When corrected To clear or reset the Memory condition set the dip switch Off and back Stored trouble conditions Memory are indicated on the LeD associated with the trouble condition following two 2 diagrams illustrate the dip switch settings for the pSN 106 and the pSN 64 respectively 2 Examples of Dip Switch S8 Settings on the PSN 106 PSN 64 position ON Memory Memory Disabled Memory Enabled Power Config DC Power is constant DC Power is Door Holder Holder OFF 15 sec delay after AC loss OFF 60 sec delay after AC loss ON 5 min delay after AC loss ON No dropout after AC loss 5 6 Class A B Select Class B Class A 3 4 Class A B Select Class B Class A 1 2 Class A B Select Class B Class A 3590 16 position ON Memory Memory Disabled Memory Enabled Power Config DC Power is Constant DC Power is Door Holder Holder OFF 15 sec delay after AC loss OFF 60 sec delay after AC loss ON 5 min delay after AC loss ON No dropout after AC loss 3 4 Class A B Select Class B Class A 1 2 Class A B Select Class B Class A 3590 16 B page 2 OF 5 Electric Signal Company LLC St Louis MO Phone 800 325 3936 www pottersignal com8870042 REv A 6 16PSN Series Dip Switch Programmingfirealarmresources com NAC Options NaC may be individually programmed and activated according to the option selected The Selection specifies input s will respond as described in the table below 1 2 1 or Trigger 2 DC Power ON Selection 3 NAC Dip Switch Settings will activate when Trigger 1 is activated will activate when Trigger 2 is activated will activate when either Trigger 1 or Trigger 2 is activated Can be used to separately control horns strobes when used with one of the supported protocols Trigger 1 is present both horns and strobes will be activated only Trigger 2 is present horns will be disabled and strobes will be activated Strobes remain active when horns are silenced used to create additional door holder power circuits to create a constant unsupervised power output circuit will be unused eOL not required following diagram illustrates dip switch settings for the individual NaC options on the pSN 106 and pSN 64 power supply 3 Example of Individual NAC Dip Switch Settings on the PSN 106 PSN 64 position ON Select OFF OFF Constant OFF OFF ANSI Temporal ON OFF Pass Through Input Tracking ON OFF Amseco Sync OFF ON Gentex Sync OFF ON System Sensor Sync ON ON Wheelock Sync Select OFF OFF Trigger 1 OFF OFF Trigger 2 ON OFF Trigger 1 or Trigger 2 ON OFF Combo Trigger OFF ON Follow DC power OFF ON Always on ON ON Always on ON ON Always off NAC is unused and unsupervised Trigger 1 for horns Trigger 2 for strobes 3590 11 page 3 OF 5 Electric Signal Company LLC St Louis MO Phone 800 325 3936 www pottersignal com8870042 REv A 6 16PSN Series Dip Switch Programmingfirealarmresources com Supply Dip Switch Settings two 2 Supply programming options are described below Report Delay 4 Bulk Supply Dip Switch Settings number of hours to delay before activating the general trouble relay in to a low aC condition Note that the Low aC relay is activated immediately should always be in the position to allow supervision of the wiring the 24 VDC bulk supply board and the NaC control board 4 Example of Bulk Supply Dip Switch Settings position ON Bulk with NAC Bulk only Delay OFF 1 Hour OFF 3 Hours ON 6 Hours ON 30 Hours 3590 1 page 4 OF 5 Electric Signal Company LLC St Louis MO Phone 800 325 3936 www pottersignal com8870042 REv A 6 16PSN Series Dip Switch Programmingfirealarmresources com LED Behavior for NACs NaC control board contains an Indicator LED for each NaC circuit and a Comm LED as described below Type LED 5 NAC LED Behaviors Fast Flashing NaC trouble indicating eOL missing eOL shorted or current limit condition one 1 per second supervision activity between bulk and control board is present or Pattern NaC is active LeD follows pattern of NaC The Power LED is always illuminated the Memory option is enabled Memory dip switch option the LeDs indicate if any previous trouble are stored in memory Memory is enabled and a NaC circuit eOL is detected as missing Clear Reset Trouble Memory by setting Dip Switch Switch 8 Memory dip switch and then back to enable the feature LEDs for Bulk Supply Board Bulk Supply board contains four 4 indicator LeDs descri