Potter SH-1224 Series Horn Strobe

SH 1224 SERIES MOUNT UL and cUL listed 12 VDC with 15 35 or 60 cd setting 24 VDC with 15 35 60 75 95 or 110 cd settings 6 distinct candela settings Candela selection view window 15 75 ADA compliant on 60cd setting 33 sound output settings Horn or chime sound output Pre wire back plate Universal back plate mounting single gang double gang octagon or 4 square Single screw mounting Indoor only Low current draw SH 1224 Strobe Horn Series provides a wide range of candela output options in a single device The candela settings include a or 24 volt DC operation for the 15 35 and 60 75 on axis candela and 24 volt DC operation for the 15 35 60 75 95 and 110 settings The candela setting is displayed through the front and is selectable using a drum wheel horn settings include Temporal Non Temporal March Time a Chime sound The horn also has Low Mid and High volume for each pattern and tone The tones include 2400 Hz Electro Broadband and Chime voltage input can be either regulated DC or full wave rectified 12 volt or 24 volt operation with an operating range from 8 to V DC The strobes can be synchronized using a control panel with Potter Amseco sync protocol or a SMD10 3A sync module SH 1224 utilizes a universal mounting plate that will mount on a gang double gang octagon and 4 square electrical boxes The plate allows the installer to mount the plate and connect the wire The strobe attaches in a hinge fashion from the top and is by a single mounting screw The strobe completely covers the back plate therefore it can be mounted before other trades is completed and not affect the final look jumper plug is provided to test for correct in the supervisory mode only Do not alarm current through the jumper Installation must comply in accordance with applicable standards Information Number Number strobe horn chime strobe horn chime Electric Signal Co LLC St Louis MO Cust Service 866 240 1870 Tech Support 866 956 1211 Canada 888 882 1833 www pottersignal com IN USA MKT 8910004 REV F 1 OF 4 SERIES MOUNT output in precentage when measured from the following per UL 1971 inches mm 127 voltage may be present inside the light assembly even power is not connected If access to teh coponent board required removal or replacement the capacitor must be by touching a wire to both ends of the flashtube NOT attempt to touch or move the assembly until the has been discharged 1 2 3 4 5 6 7 8 Current RMS Operating Current mA RMS 12 VDC 12 FWR 24 VDC 24 FWR Designation 12 DC FWR 24 DC FWR Voltage Range 17.5V Rate Module SMD10 3A Temperature times min 33V model 32 to 120 0 to 49 Dipswitch ON Non temporal OFF Temporal Both 2 OFF and 2 ON March Time and 4 ON 2400Hz ON and 4 OFF Electromechanical and 4 OFF Chime OFF and 4 ON Broadband and 6 ON High ON and 6 OFF Mid and 6 OFF Low and 8 ON Horn strobe on 2 wires and 8 OFF Horn and strobe on 4 wires To determine total current draw add desired strobe setting and horn selection Refer to the installation instructions for further information IN USA MKT 8910004 REV F 2 OF 4 SERIES MOUNT Horn Current RMS Current RMS Current Reverberant Ratings per dBA 10 ft Anechoic Ratings per S525 dBA 10 ft 12 VDC 24 VDC 12 VDC 24 VDC 12 VDC 24 VDC Horn Current RMS Current RMS Current Reverberant Ratings per dBA 10 ft Anechoic Ratings per S525 dBA 10 ft 12 VDC 24 VDC 12 VDC 24 VDC 12 VDC 24 VDC Hz Hz Hz Time Horn Current RMS Current RMS Current Reverberant Ratings per dBA 10 ft Anechoic Ratings per S525 dBA 10 ft 12 VDC 24 VDC 12 VDC 24 VDC 12 VDC 24 VDC IN USA MKT 8910004 REV F 3 OF 4 Diagram SERIES MOUNT 8910004 1 Specifications installer shall provide and install the Potter SH 1224 selectable The strobe shall have six 6 candela settings The settings shall be selectable using a drum roller and shall the candela setting on the front of the device The horn shall 33 selectable settings configurable by dip switches The sounder be capable of ANSI Temporal Code 3 March Time and produce chime output The horn shall have three distinct volume levels strobe horn shall operate at 12 or 24 VDC regulated or full wave The strobe horn shall have an operating range between 8 and VDC the strobes an by synchronized using a control panel with Potter sync protocol or the SMD10 3A sync module The strobe utilize a mounting plate that allows the installer to pre wire the plate The mounting plate shall be universal and mount on a gang double gang octagon or 4 inch square box The mounting shall be completely covered by the strobe and shall be secured a single screw The strobe shall be UL listed to standard 1638 Signaling and standard 1971 Signaling Devices for the Impaired In addition the strobes shall be cUL listed to CAN S526 The horn shall be UL listed to standard 464 Audible Devices IN USA MKT 8910004 REV F 4 OF 4