Siemens CAB1 CAB1R System Enclosure, Installation Instructions

Installation Instructions CAB1 CAB1R Enclosure Models CAB1 and CAB1R Enclosures from Siemens Industry Inc are used to system modules The CAB1 backbox and doors are black the CAB1R backbox outer door are red They are identical in all other ways and will be referred to in remainder of this document as CAB1 The CAB1 consists of an outer door an door and a backbox as shown in Figure 1 CAB MP Mounting Plate P N 500 can be purchased as an option DOOR 1 Enclosure DOOR Enclosure is for indoor use only in dry environments backbox is mounted on a flat surface with four user supplied bolts that are a of 3 8 inch in diameter backbox contains enough space to mount a set of BTX 1 31 AH batteries in the 315 033007 9 Industry Industry Industry Inc Inc Inc Industry Inc Industry Inc TTTTTececececechnologies Di Di Di Division Di to installation consider the following the backbox Mounting height for visual and manual access to the Person Machine PMI PMI 2 PMI 3 displayed in the opening of the outer door Models LVM and FMT one module width each mount to the inner door other modules PSC 12 PSX 12 CC 5 CC 2 may be located behind modules Weight and size of the enclosure codes Select a clean dry shock and vibration free surface the backbox clear of obstructions so that the front door opens and the controls and indicators are easily accessible Mark the locations of the two upper mounting bolts of the backbox on the Refer to Figure 2 Drill the two holes located in the previous step and screw in the top bolts a small gap between the wall and each top bolt the backbox over the two top bolts and allow it to slide down over the Refer to Figure 3 Mark drill and install the two bottom bolts in the backbox all four bolts securely against the back wall of the backbox CAB1 2 Mounting Holes Industry Inc Technologies Division 315 033007 9 3 The CAB1 compliance with NEC Article 760 all power limited fire protective signaling must be separated a minimum of inch from all of the following wiring within a control panel light 1 or non power limited fire protective signaling conductors meet these requirements the following guidelines must be observed when modules and wiring to this control panel installing power limited field wiring the installer must comply with NEC article which states fire alarm power limited circuits are installed using Types FPL FPLR FPLP or substitute cable provided these power limited cable conductors extending the jacket are separated by a minimum of 0.25 in 6.35 mm or by a noncon sleeve or nonconductive barrier from all other conductors power limited wiring is not used within the CAB1 enclosure then the following do not apply In that case be sure to follow standard wiring practices Limited Wiring entering the enclosure from the bottom and right side of the backbox is non power limited wiring Wiring must be in the shortest route and must overlap any other wiring Limited Wiring entering the enclosure from the top and the left side of the backbox is power limited Wiring must be in the shortest route and must not overlap other wiring Entering Enclosure Industry Inc Technologies Division 315 033007 9 the existing lances in the backbox to dress the wires as needed to maintain of power limited and non power limited wiring Wiring primary mains input must have a separate or dedicated circuit breaker Wire in with local codes and NEC 760 the knockouts in the backbox for the entry of field wiring Refer to 4 for the location of knockouts all field wiring into the backbox Do not dress the wiring until the of all the equipment is known the wiring from the external power source to the approximate of the power supply 2 1 8 TYP 3 TYP 2 3 4 TYP 14 TYP 2 1 4 1 2 NPT KNOCKOUTS DOUBLE X 1 NPT SIZE PLACES 4 Knockouts the backbox is installed and the wiring completed finish the installation by the optional mounting plate the inner door the outer door and the ground the mounting plate if used CAB MP Mounting Plate P N 500 633012 be purchased as an option the inner door by placing it on its hinges Refer to Figure 5 blank plates as needed in unused spaces on door and secure with nuts Refer to Table 1 and Figure 6 Industry Inc Technologies Division 315 033007 9 5 The Outer And Inner Doors On The CAB1 6 The Inner Door Plates 7 The Ground Straps Industry Inc Technologies Division 315 033007 9 8 The Inner Door the outer door by placing it on its hinges Refer to Figure 5 the ground straps on both the inner and outer doors Refer to Figure 7 the inner door and secure with the turn fastener The inner door can be secured with a 10 32 x 1 2 screw user provided if desired Refer Figure 8 the outer door and secure with the key latch backbox x 6 7 8 x 27 Industry Inc Technologies Division 315 033007 9 security disclaimer products and solutions provide security functions to ensure the secure operation of comfort fire safety security management and physical security systems The security on these products and solutions are important components of a comprehensive security is however necessary to implement and maintain a comprehensive state of the art security that is customized to individual security needs Such a security concept may result in site specific preventive action to ensure that the building comfort fire safety security or physical security system for your site are operated in a secure manner These may include but are not limited to separating networks physically protecting system user awareness programs defense in depth etc additional information on building technology security and our offerings contact your Siemens or project department We strongly recommend customers to follow our security advisories provide information on the latest security threats patches and other mitigation measures http www siemens com cert en cert security advisories htm Industry Inc Technologies Division 315 033007 9 PAGE HAS BEEN LEFT INTENTIONALLY BLANK Industry Inc Technologies Division Park NJ Canada Ltd North Service Road East Ontario 0H6 Canada ID A6V10324415 315 033007 9