Siemens CAB1-X System Enclosure for NCCNT WAN, Installation Instructions

Installation Instructions CAB1 X Enclosure for NCCNT WAN Model CAB1 X enclosure from Siemens Industry Inc is used to house system The CAB1 X backbox and doors are black The CAB1 X consists of an outer an OD GP vented grill plate a mounting plate CAB MP and a backbox as in Figure 1 GRILL PLATE DOOR PLATE 1 Enclosure backbox is mounted on a flat surface with four user supplied bolts that are a of 3 8 inch in diameter backbox contains enough space to mount a set of BTX 1 31 AH batteries in the Optional the CAB MP mounting plate from the backbox 315 034369 4 Industry Inc Technologies Division to installation consider the following Mounting height for access to the opening of the outer door Weight and size of the enclosure codes the backbox Select a clean dry shock and vibration free surface the backbox clear of obstructions so that the front door opens freely the controls and indicators are easily accessible Mark the locations of the two upper mounting bolts of the backbox on the Refer to Figure 2 Drill the two holes located in the previous step and screw in the top bolts a small gap between the wall and each top bolt the backbox over the two top bolts and allow it to slide down over the Refer to Figure 3 Mark drill and install the two bottom bolts in the backbox all four bolts securely against the back wall of the backbox FOR 2 Mounting Holes Industry Inc Technologies Division 315 034369 4 BOLTS PLACES SUPPLIED 3 The CAB1 X compliance with NEC Article 760 all power limited fire protective signaling conduc must be separated a minimum of inch from all of the following wiring located a control panel light 1 or non power limited fire protective signaling conductors meet these requirements the following guidelines must be observed when modules and wiring to this control panel installing power limited field wiring the installer must comply with NEC article which states fire alarm power limited circuits are installed using Types FPL FPLR FPLP or substitute cable provided these power limited cable conductors extending the jacket are separated by a minimum of 0.25 in 6.35 mm or by a noncon sleeve or nonconductive barrier from all other conductors energy limited cable or equivalent is not used within the CAB1 X enclosure then following guidelines do not apply In that case be sure to follow standard wiring Limited Wiring entering the enclosure from the bottom and right side of the backbox is non power limited wiring Wiring must be in the shortest route and must overlap any other wiring Entering Enclosure Industry Inc Technologies Division 315 034369 4 Limited Wiring entering the enclosure from the top and the left side of the backbox is consid power limited Wiring must be in the shortest route and must not overlap any wiring the existing lances in the backbox to dress the wires as needed to maintain of power limited and non power limited wiring Wiring System is designed to operate from an external 120 VAC 60 Hz power source primary mains input must have a separate or dedicated circuit breaker Wire in with local codes and NEC 760 the knockouts in the backbox for the entry of field wiring Refer to 4 for the location of knockouts all field wiring into the backbox Do not dress the wiring until the of all the equipment is known the wiring from the external power source to the approximate location the power supply the backbox is installed and the wiring completed finish the installation by the mounting plate the outer door the OD GP grill plate and the ground the mounting plate if removed the door by placing it on its hinges Refer to Figure 5 page 5 the OD GP vented grill plate on the door and secure with the 10 32 supplied Refer to Figure 6 page 5 the ground strap on the door Refer to Figure 7 page 6 backbox x 6 7 8 x 27 Industry Inc Technologies Division 315 034369 4 PLACES 4 Knockouts 5 The Door On The CAB1 X GRILL PLATE DOOR 6 The OD GP Grill Plate On The CAB1 X Door Industry Inc Technologies Division 315 034369 4 STRAP DOOR 7 Strap Installation Industry Inc Technologies Division 315 034369 4 page has been left intentionally blank Industry Inc Technologies Division 315 034369 4 page has been left intentionally blank Industry Inc Technologies Division Park NJ Building Technologies Ltd Safety Security Products Kenview Boulevard Ontario 5E4 Canada 315 034369 4