Siemens CPY-150, CPY-250 Cylinder Valve Assemblies – 1-1 2 Inch Discharge Port, Data Sheet

Sheet Safety Products Engineered Fire Suppression Systems Valve Assemblies 1 1 2 6.4 cm Discharge Port Cylinder Mounting Straps Brackets Top Plug Adapter Liquid Level Indicator Low Pressure Switch CPY 150 CPY 250 AND ENGINEER SPECIFICATIONS For use with Sinorix 227 and Sinorix 1230 High flow rate valve 1 1 2 inch discharge port valve assembly Manual electric or pressure operated Low pressure monitoring switch Wall mounting brackets included Liquid level indicator UL Listed ULC Listed FM Approved Overview CPY 150 CPY 250 are filled as follows Lbs Lbs Fill at LB FT3 Lbs Lbs Fill at LB FT3 Lbs Lbs CPY 150 and CPY 250 can be filled with suppression agent or with 3M 1230 Fire Protection Fluid Models and CPY 250 are pressurized with to 360 psig at 70 21.1 and manufactured tested and marked in with D O T or 4BW500 for the various sizes cylinder and valve assemblies are furnished an internal siphon tube Cylinders must be in the vertical position size 150 and 250 lbs cylinders use a valve a 1 1 2 6.4 cm unified victaulic outlet pressure seated valves are designed for rates Additionally each valve meets rapid discharge time specified in NFPA 2001 valve assemblies have Brass body Brass piston with resilient seat Safety disc assembly Pressure gauge Pressure releasing pilot check assembly for and pressure actuation which relieves pressure above the piston and permits piston to travel upward Optional electronic solenoid on the valve relieves the pressure above the piston permits the piston to travel upward Valve Assemblies 1 1 2 Discharge Port Sinorix 6621 Industry Inc Technologies Division Actuator Manual Control Combination Ft Ft Qty of Piston Lbs Lbs Manual Control Head may be installed using the electronic top plug adapter for Ordering Lbs Lbs Lbs Lbs of empty cylinders and Valve Assembly continued Controls valve sizes accept the same set of valve Solenoid Valve Electronic Solenoid Valve is normally closed and opens upon electric energy being therefore relieving pressure above the piston and causing the cylinder valve to For electrical connections the Electronic Valve is furnished with 24 61 cm 500 697990BG Electronic Supervised Solenoid Manual Control Head Local Manual Control Head can be installed on top plug adapter When the safety pull pin is out and the actuating lever is moved down causes a pin to depress and open the pilot check the valve pressure is then released the valve piston Actuator Pressure Actuator can be installed on the top adapter The Pressure Actuator contains a to provide the necessary force to open the check once pressure from the agent of a primary cylinder is applied through 0.64 cm tubing The pressure actuator is on pressure operated secondary cylinders are released simultaneously with the Sinorix cylinder 1 primary cylinder can be used to pressure up to a maximum of seven 7 secondary If more than seven 7 cylinders are the engineer may use two 2 electric Sinorix cylinders cylinder valves have a pressure actuation outlet The pressure actuation outlet port opens into same space as the valve outlet and is only pressure while the valve is discharging The has a 1 8 0.32 cm pipe victaulic which is with a pipe plug The pipe plug is removed the port is used The tubing or pipe is to the outlet M and is run to the actuators on the secondary cylinders Industry Inc Technologies Division Mounting Straps Brackets steel straps and brackets are used to the cylinders in the vertical position Indicator Liquid Level Indicator works magnetically it is not necessary to move or disconnect Uninterrupted hazard protection is key feature brackets which are used for wall purposes are secured to adjacent studs The brackets and straps are UL ULC Listed as well as FM Approved Liquid Level Indicator must be factory and is UL Listed ULC Listed well as FM Approved Liquid Level Indicator 1 Cylinder Maintenance Switch Sinorix Low Pressure Indicating Switch CPY PSS1 is a single pole single switch that is mounted to the cylinder during production CPY PSS1 will remain in the NC when no pressure is set against the In Normal operating position the switch must be set at 360 psig the cylinder valve is pressurized Model will move into the open position loss of pressure from the cylinder valve due to discharge or leakage Model CPY will move to a closed position at Model CPY PSS1 is monitored by a point on the fire alarm control FACP The FACP will provide a alarm upon of pressure the PSIG set point Industry Inc Technologies Division This marketing data sheet is not intended to be used for system design or installation purposes the most up to date information refer to each product installation instructions Industry Inc Technologies Division Safety Fernwood Road Park NJ 07932 973 593 2600 908 547 6877 www USA Siemens com Fire Safety North Service Road Oakville Ontario 0H6 Canada 905 465 8000 www Siemens CA in U S A 2016 sheet dated 8 2015 6