Siemens D2325CPS Single Mode (1310nm) Fiber Optic Interface, Installation Instructions

Installation Instructions D2325CPS Mode 1310nm Fiber Optic Interface Model D2325CPS from Siemens Industry Inc See 1 is a Fiber Optic interface for the MXL RS 485 MNET or XNET FireFinder XLS Desigo Fire Modular Cerberus PRO Modular network or XNET and HUB 4 FSI It uses a two fiber pair between each device The D2325CPS can as either a repeater or an end point unit NOT USE 4 NOT USE 3 DATA 2 DATA 1 VDC 1 Module D2325CPS can operate in either a daisy chain Figure 2 or star configuration See Figure 3 allows for network configurations that are not with the RS 485 network alone D2325CPS module is not listed for use by Mutual Applications requiring fiber con of voice modules systems are therefore Factory Mutual listed not use the D2325CPS with CXL Systems Industry Inc Technologies Division Park NJ 315 050019 6 D2325CPS has four keyhole slots for 6 screws the device in the locations listed below using four 6 screws provided bracket P N 500 692880 is available for mounting D2325CPS in any MXL enclosure that will accept MOM 4 See Figure 4 This bracket has the same as the MOM 4 and accommodates two modules An assembly kit is included with bracket that contains four nuts and eight screws the bracket in the enclosure with the four nuts the positions labeled X See Figure 4 Start four of 6 32 screws and slip the keyhole slots in the over them Tighten the four screws 3 style rails that mount on an MBR 2 or MME 3 P N MSR 1 are also available and can be for mounting the D2325CPS with the System 3 Bracket Up to three brackets can be installed on single rail bracket Model D2300 MP is available for mounting D2325CPS modules in any FireFinder XLS Fire Safety Modular Cerberus PRO Modular enclosure The D2300 MP fits in the same as a CC 5 and mounts to the CAB MP A kit is provided for attaching the D2300 MP to CAB MP and mounting two D2325CPS modules the D2300 MP Mount the D2325CPS modules to installing the D2300 MP onto the CAB MP that when using two D2325CPS modules the two mounting holes on each D2325CPS share two center studs on the D2300 MP See Figure 5 CONNECTIONS INPUT D2325CPS uses filtered or unfiltered 24 VDC D2325CPS can only be powered from the listed in Table 1 on page 6 Canada Ltd North Service Road East Ontario 0H6 Canada MODE DUPLEX OPTICAL FIBER MODE DUPLEX OPTICAL FIBER BUDGET MAX LOSS dB 9 125 FIBER BUDGET MAX LOSS dB 9 125 FIBER OHMS 1 4W 140 820150 OHMS 1 4W 140 820150 OHMS 1 4W 140 820150 NODES MAX OHMS 1 4W 140 820150 NODES MAX THE 120 W 5 RESISTOR ASSEMBLY APPLICABLE 140 820150 MMB 1 2 P N 140 049099 MMB 3 NODES MAX OHMS 1 4W 140 820150 Chain Configuration MNET Shown 2 MODE DUPLEX OPTICAL FIBER BUDGET MAX LOSS dB 9 125 FIBER ADDITIONAL NODES MAX THE 120 W 5 RESISTOR ASSEMBLY APPLICABLE 140 820150 MMB 1 2 P N 140 049099 MMB 3 OHMS 1 4W 140 820150 3 Configuration MNET Shown 500 692880 POWER TO PROTECTION the D2325CPS in an MBR 2 or MME 3 Backbox 4 OPTIC CABLE LIMITED HNET XNET AS SHOWN FAIL FAIL FAULT STATUS A OPEN A RETURN A OPEN A RETURN NETWORKS FAIL FAIL FAIL FAIL FAULT A FAIL B FAIL STYLE 7 4 FAULT FAIL FAIL FAIL FAULT 12A FAIL 4A FAIL the D2325CPS in a CAB 1 Backbox 5 the D2325CPS as both a Repeater and End Point Unit BUDGET MAX LOSS 11 dB 9 125 FIBER BUDGET MAX LOSS 11 dB 9 125 FIBER POINT NETWORK FIGURES 7 8 9 POINT NOT USE NOT USE 6 THE 120 W 5 RESISTOR ASSEMBLY APPLICABLE 140 820150 MMB 1 2 P N 140 049099 MMB 3 RATINGS P P MAX OHMS MAX AWG MIN NOT USE NOT USE 4 MNET OHMS 1 4W 140 8