Siemens FMT-A-ADPT Class A Riser Module for the FMT, Installation Instructions

Installation Instructions FMT A ADPT A Riser Module for the FMT Model FMT A ADPT module as shown in Figure 1 from Siemens Inc provides the FMT with Class A riser capability The riser is supervised by the primary FMT FMT A ADPT is shipped with the bracket for use on the CC 2 or Card Cages attached to the FMT A ADPT board use the FMT on a CC 2 Card Cage y y y y you must place it in use the FMT use the FMT on a CC 2 Card Cage on a CC 2 Card Cage must place it in must place it in use the FMT A ADPT on a CC 2 Card Cage must place it in on a CC 2 Card Cage use the FMT must place it in 1 t 1 t 9 1 9 1 of the top Double Header on a CC 5 Card of the top Double Header on a CC 5 Card 9 16 of the top Double Header on a CC 5 Card 1 terminals 9 1 of the top Double Header on a CC 5 Card 9 1 1 t 1 t of the top Double Header on a CC 5 Card y y must place it in Slot 5 t must place it in Slot 5 t 9 1 9 1 of the top Double Header of the top Double Header of the top Double Header 9 16 of the top Double Header must place it in Slot 5 terminals 9 1 you must place it in Slot 5 t 9 1 y y must place it in Slot 5 t of the top Double Header 1 PCB FMT A ADPT is shipped with two removable terminal plugs Figures 5 and 6 that are installed in J1 and J2 Remove the plug from the CC 5 CC 2 header terminals 9 16 where the FMT A ADPT will installed Transfer the existing field wiring in the connector to connector J2 as in the wiring section and discard the connector that was removed all system power before installation first battery then AC To power up the AC first then the battery the FMT A ADPT Refer to Figure 2 in the top header of the CC 5 CC 2 Insert female plug on the end of the FMT A ADPT into the appropriate top header Slot 5 CARD CAGE SCREW FMT A ADPT IN SLOT 5 CC 5 CARD AS SHOWN CC 2 CARD CAGE IN SLOT 1 USE THIS SPACE CAPTIVE SCREW XLS SINGLE MODULE FOR CAPTIVE IN SLOT 1 OF TOP DOUBLE HEADER FOR CAPTIVE IN SLOT 5 OF TOP DOUBLE HEADER PLUG TOP DOUBLE MODULE INTO TOP HEADER OF 5 OF CC 5 OR 1 OF CC 2 CARD BOTTOM 2 3 Installed in CC 5 315 050338 0 Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di CC 5 or Slot 1 for CC 2 and then secure the retaining bracket under the XLS retaining captive screw that shares the space Do not put the FMT A ADPT the bezel of the XLS module Refer to Figure 3 46 inch long 10 wire audio cable P N 555 150509 connects the FMT A ADPT to FMT to provide Class A riser capability One end of this wire plugs into J4 of the and the other end plugs into JP1 of the FMT The connectors are keyed fit only one way Make sure that all cables seat fully into their connectors any existing field wiring that was in positions 9 16 of the terminal block to the corresponding position on J2 screw terminals for J2 can accommodate one 12 22 AWG or two 16 24 AWG only For J1 the screw terminals can accommodate one 12 22 AWG or 16 18 AWG stranded only All wiring to the FMT A ADPT is power limited CONNECTION 4 to J1 Connect External Wiring the wire to be connected in the desired opening in the side of the remov terminal block Tighten the appropriate locking screw the removable terminal block in the appropriate header J1 or J2 on the 8 SCREWS SCREWS 1 IN FOR WIRE 16 IN FOR WIRE 9 5 for J1 Positions 1 8 6 for J2 Positions 9 16 RATINGS Building Technologies Ltd Safety Security Products Kenview Boulevard Ontario 5E4 Canada Industry Inc Technologies Division Park NJ 315 050338 0