Siemens FMT Fireman’s Master Telephone, Installation Instructions

Installation Instructions FMT Master Telephone Model FMT Fireman Master Telephone from Siemens Inc provides firefighters with an emergency telephone for communication with remote locations The FMT is in a FireFinder XLS Desigo Fire Safety Modular Cerberus Modular enclosure and includes a handset for the operator the telephone system FireFinder XLS Desigo Fire Safety Modular Cerberus PRO systems with multiple FMT Fireman Master Tele one FMT is configured as the primary FMT and up to secondary FMT modules may be connected The telephone is supervised by the primary FMT with an EOL resistor at the end of the telephone riser See Figure 5 for a B riser The FMT can be optionally used in conjunction with FMT A ADPT module P N 500 150338 to be wired as a Class A See Figure 6 FMTs marked A See Figure 2 support Class A risers 1 Fireman Module back panel of the FMT contains four LEDs two CAN address switches and one jumper header J1 as shown in Figure 2 Factory released FMTs are as primary with all five jumpers installed function of the LEDs are defined as follows Power Card Fail ON When illuminated indicates that for the FMT is applied to the module OFF When illuminated indicates that card microprocessor has failed CAN Fail OFF When illuminated indicates that the communication with the FMT has terminated Riser Fail OFF When illuminated indicates that the between the FMT and the TZC 8B is faulted the board address for the FMT using both of the ten position rotary switches on the back of the board See Figure 2 Each of these addresses must be a of the DAC NET and must be the same as the addresses assigned in Zeus Programming Tool Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di and Indicators 315 034100 11 released FMTs are configured as primary FMTs with five J1 jumpers installed configure an FMT as secondary remove all five J1 jumpers Refer to Figure 2 CABLE CABLE CONNECTION CONNECTION SWITCHES 3 3 A FMT CLASS A 2 Cable Connections Diagnostics Address Switches and Configuration Jumper FMT mounts to the rear of the inner door in the CAB 1 CAB 2 CAB 3 or enclosures Select the location of the FMT It can be mounted on either of the PMI PMI 2 PMI 3 XLS FCM2041 U2 Desigo Fire Safety Modular Cerberus PRO Modular the two mounting studs in the desired Secure the FMT to the inner door the two nuts provided Refer to 3 XLS DESIGO SAFETY MODULAR CERBERUS MODULAR DOOR selecting the location to mount the keep in mind that no modules or supplies extenders can be installed in space on the CAB MP directly behind the primary Class A FMT can not be installed a REMBOX 4 cable CCL optional a 30 inch long 6 cable P N 599 634214 or CAN cable 555 134100 an 8 inch long 6 wire connects the FMT to the next CAN or to P3 on the CC 5 CC 2 24 inch long 10 wire audio cable 555 134260 connects the FMT to P4 P5 on the LVM If there is no LVM in the configuration connect the audio cable to on the CC 5 CC 2 or to JP6 on the PMI PMI 2 PMI 3 XLS FCM2041 U2 Desigo Safety Modular FCM2041 U3 Cerberus PRO Modular Refer to Figure 4 3 FMT to Rear of Inner Door modules marked A See Figure 2 must use the 6 wire version of this Use of the 10 wire cable will result in an erroneous ground fault indication on PSC 12 sure that all cables seat fully into their connectors Secure the cable in the back using cable ties and the tie down points in the enclosure The cable must have slack to allow the inner door to open fully without putting stress on the cable Industry Inc Technologies Division 315 034100 11 to Figure 5 for FMT Class B Riser Wiring and Figure 6 for FMT Class A Riser Wiring all system power before installation first battery then AC To power up the AC first then the battery FMT module is a node in the CAN bus FMT connects through the CC 5 CC 2 CAN bus via a plug in cable to DAC NET to 99 CAN modules in any combination can be connected to the CAN of each DAC NET FMT module is shipped with one FMT CABLE P N 555 134100 connections are shown in the following table and in Figure 4 LVM CC 5 2 XLS DESIGO SAFETY MODULAR CERBERUS MODULAR OR RNI CC 5 2 OR RNI NEXT CAN MODULE 2 3 4 6 7 8 9 2 3 4 6 7 8 SWITCHES RNI INSTALLATION INSTRUCTIONS P N 315 033420 4 Cable Connections CAN bus requires a 120S resistance at each end of the loop Refer to the Installation Instructions P N 315 035100 for details about CAN termination Industry Inc Technologies Division 315 034100 11 RATINGS FAIL FAIL FAIL FAULT 12A FAIL 4A FAIL All wiring must be in with NFPA 70 or building codes All output circuits are power to NFPA 70 and 100 max Use twisted pair or shielded pair The FMT must be located at end of the riser Ground faults detected at or less FAIL FAIL FAIL FAULT 12A FAIL 4A FAIL FAIL FAIL FAIL FAULT 12A FAIL 4A FAIL FAIL FAIL FAIL FAULT 12A FAIL 4A FAIL FAIL FAIL FAIL FAULT 12A FAIL 4A FAIL RESISTOR 140 034726 LOCATED IN ENCLOSURE WITH PSC 12 1 IS THE PRIMARY FMT LOCATED IN ENCLOSURES WITH PSC 12 2,3,4 AND 5 ARE SECONDARY FMTs RESISTOR 140 0