Siemens FP2011-U1 6 5 Amp Power Supply Module, Installation Instructions

Installation Instructions FP2011 U1 Amp Power Supply Module Model FP2011 U1 is a modular power supply that primary regulated 26VDC power for normal The FP2011 U1 is rated at 6.5A and is filtered regulated Regulation is 0.25V under all load cases module incorporates a 4.0A non resettable slow fuse on the primary input and includes a built in line filter for surge and noise suppression The mounts in a standard enclosure are no serviceable parts to be maintained all system power before installa first battery then AC To power up the AC first then the battery installation kit for the FP2011 U1 includes the module lock nuts cable 240VAC installation reference the Removal section on page 2 installing the FP2011 U1 module the enclosure to the wall before mounting the power supply to the enclosure Make sure that the dedicated circuit breaker for FP2011 U1 is turned off at the mains Place the FP2011 U1 housing over the four studs in the enclosure indicated in the system manual Refer to Figure 1 for a typical Industry Inc Technologies Division Park NJ 315 050222 2 Using the lock nuts provided secure the FP2011 to the mounting studs of the enclosure Enclosure Mounting 4 places Mounting in Typical Enclosure 1 FP2011 U1 is designed to operate from a 120 or VAC 50 60 Hz power source Use a separate or circuit breaker Wire in accordance with the having jurisdiction and Article 760 of the NEC 70 latest edition the earth ground from a suitable source to the Check local requirements Conduit is not acceptable earth ground conductor Connect the AC mains to the 3 position terminal on the FP2011 U1 as shown in Figure 2 Live N Neutral G Earth Ground Canada Ltd North Service Road East Ontario 0H6 Canada the AC input is 240VAC you will need to remove cover of the FP2011 U1 housing and remove the on J1 Follow the steps listed below On the side of the housing with 5 screws remove 5 screws and place them to one side On the side of the housing with 8 screws remove 5 screws indicated in Figure 4 and place them to side NOT REMOVE THE REMAINING 3 SCREWS Connect the 4 wire cable included in the installation to the 4 position header on the FP2011 U1 The is keyed and will connect in only one way the other end of the cable to the terminal TB indicated in the system installation This cable is also keyed and will connect only one way Refer to Figure 3 L N G AWG MIN 2 the FP2011 U1 WITH CONNECTOR PCB BOARD WITH SUPLY RATINGS Power or 240VAC 2.0A Max 26VDC 6.5A Max Current 6.5A 2 Hours Max and Regulated REMOVAL FOR 240VAC ONLY all system power before installa first battery then AC To power up the AC first then the battery 315 050222 2 4 5 Screws from the Side of the that has 8 Screws Take off the top cover Locate jumper J1 Refer to Figure 5 to find the 3 Power Supply Cable PCB 240VAC Remove Jumper 5 of Jumper J1 for 120VAC on the FP2011 U1 Supply For 240VAC Remove Jumper Remove J1 by hand or by using a tool Replace the top cover on the FP2011 U1 and in place by installing the 10 screws that removed security disclaimer products and solutions provide security functions to ensure the secure operation of building fire safety security management and physical security systems The security functions on products and solutions are important components of a comprehensive security concept is however necessary to implement and maintain a comprehensive state of the art security concept is customized to individual security needs Such a security concept may result in additional site preventive action to ensure that the building comfort fire safety security management or security system for your site are operated in a secure manner These measures may include are not limited to separating networks physically protecting system components user awareness defense in depth etc additional information on building technology security and our offerings contact your Siemens or project department We strongly recommend customers to follow our security advisories provide information on the latest security threats patches and other mitigation measures http www siemens com cert en cert security advisories htm 315 050222 2 PAGE HAS BEEN LEFT INTENTIONALLY BLANK 315 050222 2 ID A6V10333499