Siemens Scalance X204-2 Multimode and X204-2LD Single Mode Ethernet Fiber Switch, Installation Instructions

Installation Instructions Scalance X204 2 Multimode and X204 2LD Single Mode Fiber Switch Switch Ethernet Connections Model Scalance X204 2 Multimode and X204 2LD Single Ethernet Fiber Switch as shown in Figure 1 from Building Technologies Inc is used to maintain a Style ring or Style 4 Class B wiring for communications between buildings and Siemens Building Management Systems Fire Centers within a GCNET campus Desigo CC DMS Both Style 7 and Style 4 perform all required of the health of the network Style 7 wiring will the ring when a break or other failure is The failure is reported via SNMP Simple Management Protocol fiber switch obtains its power from a 24V UL Listed for Application Power Limited Regulated Power Supply It connectors for the fiber cable and four RJ45 network connections Style 7 the fiber switch that is connected to the primary Station is designated as the ring master There no differencein installation configuration and operation of mode or multimode fiber optic switches except the type of fiber used 1 X204 2 Ethernet Switch all system power before installation first battery then AC To power up the AC first then the battery fiber switch mounts on a bracket in the lower left corner of the VNT MP mount plate as shown in Figure 2 To mount the fiber switch on the bracket place the edge of the fiber switch cutout on the bottom edge of the rail between the and the standoff and then snap the top edge of the fiber switch cutout on to top edge of the rail Refer to Figure 3 for the mounting detail FOR SWITCH PLACE BOTTOM EDGE OF SWITCH GROOVE ON EDGE OF RAIL FOR SWITCH KEEP PLACE 2 Switch Mounting on VNT MP 3 Switch Mounting Detail SNAP TOP EDGE OF SWITCH GROOVE TO TOP EDGE OF RAIL Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di on VNT MP 315 050537 5 4 shows the fiber switch module block wiring diagrams for both Style 7 Class and Style 4 Class B Figure 5 shows the wiring for the Fiber Switch connections Style 7 and Style 4 Class B unless statatatatated otherwise connect connect are supervised and power are supervised and power limit limit unless st unless st otherwise otherwise limited unless st are supervised and power limit connections are supervised and power otherwise unless st limit are supervised and power connect connect otherwise P5 previous P6 next 4 Class B Block Wiring Diagram 7 Block Wiring Diagram 4 7 and Style 4 Class B Block Wiring of Fiber Switch Module NOT USE P5 IN P5 OUT STYLE 4 CLASS B CONNECTION FIRST AND FIBER SWITCH P6 IN P6 OUT NOT USE CONNECTIONS ONE OR MORE ADDITIONAL VNT DESIGO CC OR DMS 5 RJ45 CABLE THAN 20 FT IN CONDUIT 5 RJ45 CABLE THAN 20 FT IN CONDUIT 5 Switch Style 7 and Style 4 Class B Wiring Connections to Figure 6 for the wiring of the fiber switch in a VNT Building configuration 7 shows the wiring of the fiber switch in a VNT FCC Fire Command Center Refer to Figures 10 and 11 for the wiring of the fiber switch to PAD 3 PAD 4 and Siemens Building Management System fiber optic cables are required between each pair of fiber switch modules Use a quality duplex fiber optic cable containing 62.5 125 or 50 125 multimode fiber or for single mode fiber Duplex fiber optic cable has two cables in a single similar to electrical zip cord Use ST style fiber connectors cont cont the fiber the fiber cable manufact cable manufact cable manufacturerurerurerurerurer reg reg reg reg regarding instruct instruct instruct for for for t t t t terminat contact the fiber the fiber cable manufact instructions for cont cont the fiber cable manufact instruct for fiber fiber fiber R R R R Refereferefereferefer to S to S to S to S to Scalance X 20 X 20 X 20 Operat Operat Instruct Instruct C790 C790 C790000000 G897 X 200 Operat Operating Instruct Instructions C790 fiber fiber X 20 Operat Instruct C790 switc switc switchesheshesheshes on fiber on fiber opt opt addit addit informat informat addit optic switc on fiber opt information on fiber additional informat switc opt on fiber informat addit Connections Industry Inc Technologies Division 315 050537 5 TO VNT BUILDING Industry Inc Technologies Division 315 050537 5 TO VNT FCC FIRE COMMAND CENTER Industry Inc Technologies Division 315 050537 5 RATINGS to Siemens Power Supply and Building Management System otherwise TheTheTheTheThe unless statatatatated otherwise connect connect are supervised and power are supervised and power limit limit unless st unless st otherwise otherwise connections are supervised and power limited unless st are supervised and power limit limit connect otherwise unless st are supervised and power connect switc switc to a PSC 1 to a PSC 1 ma ma P N 31 P N 31 or or or or or P P P P PAD 3 P N 31 P N 31 P N 31 P N 315 5 5 5 5 be connect be connect P N 315 033060 may be connect switch ma switc be connected to a PSC 1 to a PSC 12 P N 31 to a PSC 1 ma switc P N 31 P N 31 be connect or P P P P PAD 4 P N 31 or or P N 31 P N 31 for for power power power for power for P N 315 05021 for P N 31 or or power Voltage Regulated 24VDC Current 265mA 24VDC all system power befor