Simplex 2099-9149, -9152 Non-Addressable Releasing Stations with application labels (D) [moved location 3 10 08 from Non-Addressable Initiating Devices, Manual Stations]

ULC CSFM Listed FM Approved NYC Acceptance System Peripherals Manual Stations Releasing Applications fire alarm stations for releasing Double action push and pull operation with a open N O contact Current limited model is available with series 560 resistor for Style C operation limited alarm open or short trouble Operation complies with ADA requirements Pull lever protrudes when alarmed Break rod is supplied use is optional Label kit provides six varieties of releasing ordered separately Screw terminals for wiring connections resistant reset key lock keyed same as fire alarm cabinets mounting options Surface or semi flush with standard boxes or Simplex boxes Flush mount adapter kit Adapters are available for retrofitting to commonly existing boxes listed to Standard 38 Action Push Type Manual Release require that a spring loaded interference plate PUSH be pushed back to access the pull lever of single action station reducing the possibility of an activation A firm downward pull of the lever activates the alarm switch breaking an internal break rod visible below the pull lever use is optional Use of a break rod can provide additional reduction of the possibility of an accidental without interfering with the minimum pull needed for easy activation activated the pull lever latches into the alarm and remains extended out of the housing to a visible indication reset requires the use of a key to reset the station lever and deactivate the alarm switch If break rod is used it must be replaced testing is performed by physical activation of pull lever Electrical testing can be also performed by the station housing to activate the alarm switch Action Push Type Manual Release shown with sample release label AGENT DIOXIDE SYSTEM Kit 4099 9802 Selection blank area on the front of the station allows the of a label to match the specific release label kit is ordered separately to data sheet S2099 0007 for standard Simplex stations This product has been approved by the California State Fire Marshal CSFM pursuant to 13144.1 of the California Health and Safety Code See CSFM Listing for allowable values and or conditions concerning material presented in document It is subject to re examination revision and possible cancellation for use City of New York Department of Buildings MEA35 93E Additional may be applicable contact your local Simplex product supplier for the latest Listings and approvals under Simplex Time Recorder Co are the property of Safety Products Westminster 8 2007 Specifications Connections Range Range Color Lever Color Dimensions Product Selection Action Push Operation Manual Release Stations operation N O contact Style C operation N O contact series connected 560 resistor kit select the label required for the specific release application types include Clean Agent Carbon Dioxide Foam System Sprinkler and Manual release station red housing with white letters and white lever requires label kit 4099 9802 mount box aluminum trim plate for double gang switch box red trim plate for Wiremold box V5744 2 red mount kit break rod to page 3 for dimensions for retrofit refer to 4 for details to page 4 for details terminal for in out wiring for 18 to 14 AWG wire 0.82 mm2 to 2.08 mm2 to 140 F 0 to 60 C intended for indoor operation to 90 RH at 90 F 38 F with white raised lettering and pull lever are Lexan polycarbonate or equal with red raised lettering H x 3 3 4 W x 1 D 127 mm x 95 mm x 25 mm Semi Flush Mounting Reference Gang Box Mount gang box 2 1 2 deep mm RACO 500 or equal by others Square Box Mount 102 mm square box 2 1 8 54 mm minimum RACO 231 or equal supplied by others flush or with 2 mm extension NOT RECESS Square box cover plate DOWN gang cover plate 3 4 mm extension RACO 773 equal supplied by others view gang outline surface Mount Side View 8 2007 Box H x 4 W x 2 3 16 D mm x 102 mm x 56 mm separately Cast Box H x 3 7 8 W x 2 3 16 D mm x 98 mm x 56 mm separately Surface Mounting Reference Mounting For surface the preferred electrical are shown in the illustration the right Mounting Reference to page 4 for Wiremold box compatibility located and bottom DOWN mm for 3 4 threaded located top and bottom 95 mm 25.4 mm Series Manual Release Station Surface Mount Side View 2975 9178 box for reference cover open for access 8 2007 Additional Mounting Information retrofit and new installations additional mounting boxes and the required plates are shown in the illustration to right Semi flush trim for switch box 6 H x 4 1 2 W mm x 114 mm Flush Mounting Information box V5744 2 by gang switch box each H x 2 W x 2 3 4 D mm x 51 mm x 70 mm by others must be recessed into wall to 1 1 8 25.4 mm to 29 mm Surface trim Wiremold box H x 5 W mm x 127 mm mount adapter kit Black Beige cutout must be a of 6 H by 5 W 152 mm by 127 mm mm 121 mm 171 mm View 119 mm box 2 1 8 mm minimum by others Simplex and the Simplex logo are trademarks of Tyco Services AG or its affiliates in the U S and or other countries Lexan is a trademark of the General Electric Co is a trademark of the Wiremold Company 2007 Tyco Safety Products Westminster All rights reserved All specifications and other information shown were current as of document revision date and are subject to change without notice Safety Products Westminster Westminster MA 01441 0001 USA 8 2007 View