System Sensor M500R Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 Relay Control Module Operating Voltage Current Draw Operating Current Resistance Range to 32 VDC LED on 1 communication every 5 seconds used to 120 0 to 49 to 93 Non condensing H x 4.275 W x 1.4 D Mounts to a 4 square by 21 8 deep box Electrical Box CB500 Barrier CONTACT RATINGS RATING VOLTAGE DESCRIPTION A A A A A A A A VAC VDC VDC VDC VAC VDC VAC VAC 20ms 0.35 0.35 0.75 0.35 INSTALLING information is included as a quick reference installation guide Refer to control panel installation manual for detailed system information If the will be installed in an existing operational system inform the opera and local authority that the system will be temporarily out of service Dis power to the control panel before installing the modules This manual should be left with the owner user of this equipment DESCRIPTION M500R Relay Control Module is intended for use in intelligent two wire where the individual address of each module is selected using the rotary decade switches It allows a compatible control panel to switch contacts by code command The relay contains two isolated sets of contacts which operate as a DPDT switch and are rated in accordance the table in the manual Circuit connections to the relay contacts are supervised by the module The module also has a panel controlled LED This module can be used to replace an M500C module that has been for Form C operation REQUIREMENTS ensure proper operation these modules shall be connected to listed com system control panels only M500R mounts directly to 4 square electrical boxes see Figure 2A The must have a minimum depth of 21 8 Surface mounted electrical boxes are available from System Sensor The module can also mount to DNR W duct housing All wiring must conform to applicable local codes ordinances and reg When using control modules in nonpower limited applications the Sensor CB500 Module Barrier must be used to meet UL requirements the separation of power limited and nonpower limited terminals and wir The barrier must be inserted into a 4 4 21 8 junction box and the module must be placed into the barrier and attached to the junction Figure 2A The power limited wiring must be placed into the isolated of the module barrier Figure 2B Install module wiring in accordance with the job draw and appropriate wiring diagrams the address on the module per job drawings Secure module to electrical box supplied by installer shown in Figure 2A should be stripped to the appropriate length recommended strip length 1 4 to 3 8 Exposed conductor should be secured under the clamping plate should not protrude beyond the terminal block area Caution Do not loop under terminals Break wire run to provide supervision of connections 1 CONTROLS AND INDICATORS 2A MODULE MOUNTING WITH BARRIER 2B relay switch contacts are shipped in the standby open state but may have transferred to the activated closed state during shipping To ensure that the contacts are in their correct state modules must be made to communicate with the panel before connecting circuits controlled by the module 3 RELAY MODULE WIRING DIAGRAM NEXT LINE CIRCUIT SLC VDC MAX PAIR RECOMMENDED COMMON 2 CLOSED 2 OPEN 2 COMMON 1 CLOSED 1 OPEN 1 MODULES TO LISTED COMPATIBLE PANELS ONLY OR ANY WIRING TO TERMINALS 4 10 IS NONPOWER THE CB500 BARRIER IS REQUIRED THE INCLUDES A NONPOWER LIMITED LABEL MUST BE PLACED OVER THE POWER LIMITED INFORMATION ON THE NAMEPLATE LABEL DOES NOT SUPERVISE CIRCUITS ANY FAULT IN THE POWER SUPPLY IS TO THAT ZONE AND DOES NOT RESULT IN FAULT IN A SEPARATE ZONE LIMITED WARRANTY Sensor warrants its enclosed product to be free from defects in materials and under normal use and service for a period of three years from date of System Sensor makes no other express warranty for the enclosed product agent representative dealer or employee of the Company has the authority to in or alter the obligations or limitations of this Warranty The Company obligation this Warranty shall be limited to the replacement of any part of the product which is to be defective in materials or workmanship under normal use and service during three year period commencing with the date of manufacture After phoning System toll free number 800 SENSOR2 736 7672 for a Return Authorization number defective units postage prepaid to Honeywell 12220 Rojas Drive Suite 700 El Paso 79936 USA Please include a note describing the malfunction and suspected cause failure The Company shall not be obligated to replace units which are found to be because of damage unreasonable use modifications or alterations occurring the date of manufacture In no case shall the Company be liable for any consequen or incidental damages for breach of this or any other Warranty expressed or implied even if the loss or damage is caused by the Company negligence or fault states do not allow the exclusion or limitation of incidental or consequential dam so the above limitation or exclusion may not apply to you This Warranty gives you legal rights and you may also have other rights which vary from state to state System Sensor 03 11