Wheelock Eluxa low frequency sounders data sheet

Technical Data TD450159EN low frequency sounders and strobes has developed the Wheelock Eluxa low frequency sounders and sounder strobes ELFHS to meet the National Protection Association NFPA 72 low frequency sounder for sleeping rooms for both fire alarm and carbon CO signaling In a single device the Eluxa low frequency features both low and high candela settings and alarm for dual applications T3 fire and T4 CO tones efficiency LED technology high energy efficient technology leads the industry in lowest draw across the full candela range which reduces overall consumption and costs in fire alarm systems As the first appliances in the industry to utilize LED as the light this breakthrough and patented optical design resulting in efficiency enables material and system cost savings for a greater number of appliances on the notification circuit and fewer power supplies All strobe models feature and 177 candela settings for both wall and ceiling mount profile design and rich feature set the industry smallest footprint the Eluxa low frequency and sounder strobes are aesthetically pleasing as the low design does not detract from the interior decor Eluxa is rich with low and high candela settings and 3 horn patterns T3 T3 T4 in 1 device pre wire pre test via mounting with hinged feature for ease of installation and no tools for setting changes These products are suitable for indoor and ceiling mount applications The ELFHS and ELFHN models for 24V operation Special lettering ALERT CO and no lettering available and synchronization Eluxa strobes meet the 20 millisecond light pulse duration of the 2016 edition of NFPA 72 By meeting this latest xenon and LED devices can now be in the same field view Eluxa notification appliances are listed under UL Standards 1638 and 464 and under CAN ULC S525 and CAN ULC S526 appliances are Restriction of Hazardous Substances RoHS and contain no mercury or other hazardous substances addition the Eluxa product line has been UL ULC listed as with all Fire Alarm Control Panels FACP and accessories have been determined to be compatible with Exceder LED3 and RSS strobe based products including the RSS CH E EH ST HS MT S8 SA STH and Z Series The listing also includes ability to install the Eluxa strobes in the same notification zone field of view with any Wheelock RSS strobe and Exceder LED3 September 2021Supersedes August 2021 ELFHS ELFHN ELFHSC ELFHNC firealarmresources com Data TD450159EN September 2021 Meets NFPA 72 fire and CO low frequency sounder codes for rooms in a single device 3 horn patterns Energy efficient Low profile design Continuous T3 and T3 T4 Fire and CO signaling in 1 device LED technology provides industry lowest current draw Smallest footprint with sleek modern aesthetics Special lettering available ALERT CO no lettering Field selectable candela settings 110 177 cd Easy to install Mounting plate included with all models Convenient capture allows installers to easily hold the device while fastening single mount screw in place Finger slide switches No tools needed for setting changes Built in level adjustment feature and snap on grille cover screw terminals using 12 to 18 AWG wires Mounting Options ELSPKBB backboxes single gang and 4 square backboxes for wall models and backboxes and 4 square 2 1 8 deep backboxes ceiling models Strobe synchronization components Meet synchronizing standards with Wheelock DSM Sync or Power Supplies Compliance NFPA 72 2016 20 ms flash duration requirements UL 1971 UL 1638 UL 464 ULC S525 ULC S526 California State Fire Marshal CSFM ADA NFPA ANSI OSHA RoHS read these specifications and associated installation before using specifying or installing this product Visit Eaton for current installation instructions Notes Strobes are designed to flash at 1 flash per second minimum over Voltage Range Note that NFPA 72 specifies a rate of 1 to 2 flashes per second and ADA Guidelines specify flash rate of 1 to 3 flashes per second All candela ratings represent minimum effective Strobe intensity on UL 1971 520 tone is generated within the appliance itself When the switch is set for T3 the sound pattern is also generated the appliance When the selection switch is set to the product is listed for coded operations The T3 T4 or other pattern must be generated by the FACP according to alarm condition sensed by the panel fire or CO alarm the device is set to T3 T4 the appliance can switch from T3 to based upon the condition sensed by the FACP and passed to the DSM module 1 Wall Low Frequency Sounder Strobe 2 Ceiling Low Frequency Sounder 1 Horn Only Current Draw Sounders Settings 3 3 Code 4 Max Current a 2 Horn Strobe Current Draw Max Current a Sounder Strobes Voltage VDC RMS current ratings are per UL maximum RMS method UL max current is the maximum RMS current within the listed voltage range 16 33v strobes the UL max current is usually at the minimum listed voltage For the max current is usually at the maximum listed voltage For unfiltered ratings see installation instructions low frequencysounders and sounder strobes EATON www eaton comfirealarmresources com Data TD450159EN September 2021 3 Sound Output SPL UL 4 Sound Output SPL ULC 24V dBA per UL 464 a 3 3 Code 4 b per ULC S525 16 a 3 3 Code 4 5 Specification Ordering Information Candela w DSM or Power Supplies Strobes 177 177 177 177 177 177 177 177 177 177 177 177 177 177 177 177 Lettering Lettering Lettering Lettering Lettering Lettering Lettering Lettering Description Backbox Backbox LED Backbox LED Backbox Red White RMS current ratings are per UL maximum RMS method UL max current rating is the maximum RMS current within the listed voltage range 16 33v For strobes UL max current is usually at the minimum listed voltage For audibles the max current is usually at the maximum listed voltage For unfiltered FWR ratings see instructions to continuous development of our products specifications and offerings are subject to change without notice in accordance with Cooper Inc dba Eaton standard terms and condit