Notifier MA, MA SS, SS Multi-Alert Sounder, Sounder Strobe, and SS Signal Strobe

A Pittway Company 23 1998 MA SS SS Sounder Sounder Strobe SS Signal Strobe Audio Visual Appliances Sensor cid 146 s Multi Alert cid 153 sounders and sounder are uniquely suited to provide primary or second signaling for fire and security applications cid 151 System Sensor cid 146 s Multi Alert cid 153 Sounder and combination Sounder Strobe MA SS and Sig Strobe SS are UL listed for primary or secondary sig in life safety systems The MA Series and MASS provide eight different warning tones which can be during installation by arranging clips on tabs see Sounder Tone Selection diagram These clips can be in the field allowing the user to change the sound at any time after installation The Multi mounts directly to 4 101.6 mm square backboxes mounting plates are available for either flush or installations Flush installations require a 2 3 4 mm deep backbox model BB D The UL 464 com sounder has a low current consumption and is listed 12 and 24 VDC and full wave rectified unfiltered opera Model MA12 24D is suitable for outdoor applications installed in the optional System Sensor WBB Weath Back Box In Canada a rigid steel conduit must used when installing the WBB Weatherproof Back Box cid 151 The UL 1638 compliant SS Series signal is an electronic visible warning signal that flashes once every 1.5 seconds Available in either 1.5 cd or 15 cd light intensity at 24 VDC or 15 cd at 12 the strobe light uses an extremely reliable xenon flash with low current requirements The electronic circuit enclosed within the durable polycarbonate lens Eight field selectable and reversable tone outputs Mult sounder Strobe available in 1.5 or 15 cd Low current consumption May be surface mounted on standard 4 square backbox Flush or semi flush mounting available with optional plates Sounder and strobe can each be operated independently SS strobe UL listed to Standard 1638 Three year warranty for protection of life and property Intended for use in alarm notification circuit of a UL listed fire alarm control For further information refer to NFPA standards recommended practices for installation and use of appliances Fire MASSLO M Vol II and MASSLO M SSLO M MA only SS24LO M MASSLO M AND OPERATION Signal Strobe is an electronic visual warning signal flashes approximately once every 1.5 seconds The intensity strobe light uses an extremely reliable xenon tube with low current requirements The electronic is enclosed within the durable polycarbonate lens circuits are polarized to be compatible with DC alarm and satisfy code requirements for visual sig strobe works independently but it may be mounted on of the horn When mounted alone it may be either semi or surface mounted depending on the choice of plate options Installation instructions are packaged with each unit are included with each device Phillips head screws used to attach accessories Mounting options include Surface mounting Semi flush mounting Flush mounting deep box required Plaster ring mounting Weatherproof use WBB box sounders only cid 151 strobes not approved for weatherproof applications document is not intended to be used for installation purposes We try to keep our information up to date and accurate We cannot cover all specific applications or all requirements All specifications are subject to change without notice For information contact NOTIFIER Phone 203 484 7161 FAX 203 484 7118 Clintonville Road Northford Connecticut 06472 and Manufacturing System Certified to Standard ISO 9001 in the U S A cid 151 Page 1 of 4 SPECIFICATIONS shall be a System Sensor Model capable of operating at 12 and 24 VDC Sounder shall be listed to Laboratories Standard 464 for fire protection signaling systems Sounder shall have an operating tem between 31 cid 176 F and 151 cid 176 F 35 cid 176 C and 66 cid 176 C Sounder shall have eight tone options selected by means of Sounder Strobe Combination cid 151 Sounder strobe shall be a System Sensor Sounder Strobe Model capable of operating at 12 or 24 VDC Sounder strobe shall be listed to Underwriter cid 146 s Laboratories Standard for fire protection signaling systems Sounder strobe shall have an operating temperature between 32 cid 176 F and 0 cid 176 C and 49 cid 176 C Sounder shall have eight tone options which are selected by means of clip s Strobe shall be independently of the sounder and shall operate on 12 or 24 VDC Strobe shall have a minimum light output of or 15 candela and shall be UL listed as a primary signaling device SOUNDER SELECTION chart on page 3 STORING CLIPS COVER BACK TO COVER SLOT WITH STORAGE POST mm DIAGRAMS Sensor Weatherproof Back Box available Mount Flush Mount box required or Mount 2 of 4 cid 151 DN 2298 Strobe terminals 12 AWG 3.25 mm to 18 AWG 0.75 4 101.6 mm x 4 101.6 mm x 2 15 16 74.6125 8.2 oz 232.466 g Surface 4 101.6 mm x 4 101.6 mm 1 1 2 38.1 mm to 2 1 8 53.975 mm deep Semiflush 4 101.6 mm x 4 101.6 mm backbox 1 1 2 38.1 mm to 2 1 8 53.975 mm with MP SF mounting plate temperature range 31 cid 176 F to 151 cid 176 F 35 cid 176 C to voltage 12 or 24 VDC full wave rectified unfil Actual 12 volt operating voltage cannot be less than VDC or greater than 15.4 VDC actual 24 volt operat voltage cannot be less than 18 VDC or greater than 33 Sounder Listed for outdoor applications when used with the WBB backbox terminals 12 AWG 3.25 mm to 18 AWG 0.75 4 101.6 mm x 4 101.6 mm x 2 1 4 57.15 mm 5.7 oz 161.6 g Surface 4 101.6 mm x 4 101.6 mm backbox 1 1 2 38.1 mm to 2 1 8 53.975 mm Flush 4 101.6 mm x 4 101.6 mm BB D backbox 2 3 4 69.85 mm with MP F mounting Semiflush 4 101.6 mm x 4 101.6 mm stan backbox 1 1 2 38.1 mm to 2 1 8 53.975 mm with MP SF mounting plate For 12 gauge 3.25 mm or 14 gauge 2.00 mm wire 4 101.6 mm x 4 101.6 mm x 2 1 8 53.975 mm backbox is temperature range 31 cid 176 F to 151 cid 176 F 35 cid 176 C to voltage 12 or 24 VDC full wave rectified unfil Actual 12 volt operating voltage cannot be less than VDC or greater than 15.4 VDC actual 24 volt operat voltage cannot be less than 18 VDC or greater than 33 DRAW SOUND OUTPUT Sounder cid 151 MA12 24D See tone selection diagram on facing page for tab clip removal and storage This selection was previously identified as cid 147 Bell Chime cid 148 This tone may be used for private or public mode in the fire service when used with a 24 volt panel All models can be powered using full wave rectified unfiltered supplies Under no circumstances can MA12 24 PA400 or PS series devices input voltage exceed 33 VDC or be less than 9.6 VDC Measured at 10 feet 3.048 m in an anechoic chamber For average outputs the acoustical output shall meet the requirements of UL Standard 464