Potter SL-1224-WP Series Weatherproof Selectable Candela Strobe

SL 1224WP SERIES MOUNT WEATHER PROOF 12 VDC with 15 35 or 60 cd setting 24 VDC with 15 35 60 75 95 or 110 Outdoor or indoor 6 distinctive candela settings Candela selection view window 15 75 ADA compliant on 60cd setting Pre wire back plate Universal back plate mounting single gang double gang octagon or 4 square Single screw mounting Low current draw UL and cUL listed pending back plate allows the installer to mount the plate and terminate wire connections The strobe attaches in a hinge fashion from the and is secured by a single mounting screw The strobe completely the mounting back plate therefore it can be mounted before trades work is completed and not affect the final look Potter SL 1224WP is listed for both outdoor and indoor For outdoor installations the device must be mounted on matching BBX 5 back box or BBK 1 outdoor bell back box SL 1224WP Strobe Series provides a wide range of candela output options in a single device The candela settings include 12 or 24 volt operation for the 15 35 and 60 75 on axis candela and 24 volt operation for the 15 35 60 75 95 and 110 settings The candela setting is displayed through the front and is selectable using a drum wheel The voltage input can either regulated DC or full wave rectified FWR The strobes can synchronized using a control panel with the Potter Amseco sync or a SMD10 3A sync module SL 1224WP utilizes a universal mounting plate that will mount a single gang double gang octagon and 4 square electrical boxes Installation must comply in accordance with applicable Outdoor installations require the use of the optional or BBK 1 bell back box BOX Information Number Number strobe only strobe only Module box included back box Electric Signal Co LLC St Louis MO Cust Service 866 240 1870 Tech Support 866 956 1211 Canada 888 882 1833 www pottersignal com IN USA MKT 8910007 REV G 1 OF 2 Diagram inches mm SERIES MOUNT WEATHER PROOF 85.7 View 891 2 127 View 157.7 BBX 5 OUTDOOR BACK BOX 85.7 139.7 View 2 View 891 1 output in percentage when measured from the following per UL1971 RMS Operating Current mA RMS mount vertical dispersion 12 VDC Reg 12 FWR Reg 24 VDC Reg 24 FWR 8910007 1 voltage may be present inside the light assembly even though is not connected If access to the component board is required or replacement the capacitor must be discarged by a wire to both ends of the flashtube NOT attempt to touch or move the assembly until the capacitor been discharged Current All current draw shown is worst case at 40 40 Designation 12 DC FWR 24 DC FWR Voltage Range 17.5V Rate Module SMD10 3A Temperature times min 33V installations 32 to 120 0 to 49 installations 40 to 151 40 to 66 Specifications installer shall provide and install the Potter SL 1224WP selectable The strobe shall have six 6 candela settings The candela settings be selectable using a drum roller and shall display the candela on the front of the device The strobe shall operate at 12 or 24 regulated or full wave rectified FWR and shall have an operating between 8 and 33 VDC The strobes can be synchronized using a panel with the Potter Amseco sync protocol or a SMD10 3A module The strobe shall utilize a mounting plate that allows the to pre wire the mounting plate The mounting plate shall be and mount on a single gang double gang octagon or 4 inch box The mounting plate shall be completely covered by the strobe shall be secured by a single screw The SL 1224WP can be mounted and is listed for such applications In outdoor installations the shall be mounted on either a matching BBX 5 or BBK 1 back box The operating range shall be 32 to 120 0 49 for the indoor installations and 40 to 151 40 to 66 the outdoor installations The strobe shall be UL listed to standard General Signaling and standard 1971 Signaling Devices for the Impaired In addition the strobes shall be cUL listed to CAN S526 IN USA MKT 8910007 REV G 2 OF 2