Siemens NRC Network Ring Card, Installation Instructions

Installation Instructions NRC Ring Card FAIL Model NRC Network Ring card from Siemens Industry is a card that networks multiple FireFinder XLS Desigo Safety Modular Cerberus PRO Modular systems to in a Class X Style 7 ring The NRC can also be for Class B Style 4 operation in systems where a is not required as an alternative to the NIC C card provides communication between its host FireFinder XLS Fire Safety Modular Cerberus PRO Modular system other FireFinder XLS Desigo Fire Safety Modular Cerberus Modular systems on an XNET network It replaces the when a ring connection is needed NRC can also be used to connect an NCCNT G to the network In this configuration all events occurring on FireFinder XLS Desigo Fire Safety Modular Cerberus PRO network are displayed at the NCCNT G NRC is required in each FireFinder XLS Desigo Fire Modular Cerberus PRO Modular system on the This NRC must reside in the same enclosure as the XLS FCM2041 U2 Desigo Fire Safety FCM2041 U3 Cerberus PRO Modular NRC supervises the network to ensure proper operation faults that are detected by the NRC are reported to the XLS FCM2041 U2 Desigo Fire Safety FCM2041 U3 Cerberus PRO Modular for annun In addition the NRC has diagnostic LEDs that which faults have been found The NRC performs fault detection on its outgoing ring port NRC isolates faults to the individual link in trouble When for Class X Style 7 network ring communication unaffected 1 Network Ring Card RJ 12 monitor jack is included for connection of XNET diagnostic tools In addition and USB jacks are included for firmware download These jacks are located on front bezel 4 ULC DCLB 7 ULC DCLC Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di NRC continuously monitors the network for activity and reports any problems to PMI PMI 2 PMI 3 XLS FCM2041 U2 Desigo Fire Safety Modular FCM2041 U3 PRO Modular In some cases a reset at the PMI PMI 2 PMI 3 XLS Desigo Fire Safety Modular FCM2041 U3 Cerberus PRO Modular is to clear network troubles and Indicators front panel of the NRC contains one reset switch three one Monitor port one USB port and one Ethernet port as shown in 1 reset switch is located on the top of the front panel Pushing the reset switch the NRC LEDs follow the reset switch and their functions are defined as follows FAIL ON When illuminated indi that power for the NRC is applied the card OFF When illuminated indicates the card microprocessor has failed OFF When illuminated indi trouble in the Network such as faults or module failure The Trouble will illuminate under the following Wire faults open or short in either 1 In or Port 2 Out Figure 5 Ground fault on outgoing port Port 2 XNET communications problems the PMI PMI 2 PMI 3 XLS Desigo Fire Safety FCM2041 U3 Cerberus PRO and the NRC NRC does not have a network address but it does need to be included in the configuration NRC plugs perpendicularly into one slot in the CC 2 or CC 5 card cage via two DIN connectors only 64 pins are used and can occupy any slot in the card Refer to Figure 2 the NRC card into the card guides front bezel up lettering on the front is legible until the card cage connectors contact the motherboard that the card edge connectors align properly with the motherboard There is only one correct way to plug in the card If it does not DO NOT FORCE the card Place thumbs on the front panel adjacent to captive screws and gently apply even pressure on the card until the plug firmly into the motherboard receptacles Secure the NRC to card cage with the captive screws 2 the NRC Industry Inc Technologies Division UPGRADES NRC Software Version time to time modules used in XLS Desigo Fire Safety Modular Cerberus PRO systems are upgraded to improve their operation or to add to their capabili with new features Firmware in the NRC is field upgradable Refer to the Zeus Manual P N 315 033875 and Zeus Help for additional details check for the current version of NRC software in an installed NRC go to the PMI XLS FCM2041 U2 Desigo Fire Safety Modular FCM2041 U3 PRO Modular and press the Menu button select Report press the More button and select the Operator Interface OI Press the Configuration soft key Appl Rev for the Application Version The NRC software version will be with the OI software version Refer to Figure 3 for an example of a display FireFinder PMI C 253 Rev Report Version text information 3 OI Display of NRC Software Version Industry Inc Technologies Division all system power before installation first battery then AC To power up the AC first then the battery field wiring to the NRC is connected to the terminal blocks of the CC 2 or CC 5 cage slot in which it is installed connect the field wiring the screw of the terminal by turning it counterclockwise the wire into the side of the terminal block the screw of the terminal block by turning it clockwise screw terminals can accommodate one 12 22 AWG 4 Wiring HEADER OF BLOCK THE CC 5 CC 2 2 1 No EOLR required 22 AWG min 12 AWG max 3300 feet max per pair NRCs or Unshielded pair with a minimum 3 twists per ft to Table 1 for NRC specifications Terminate shields at one end Power limited to NFPA 70 All wires supervised Ground fault detected at ohms or less NOT USE NOT USE NOT USE NOT USE NOT USE NOT USE NRC NRC SLOT OF CC 5 SLOT OF CC 5 SLOT OF CC 5 NOT USE NOT USE NOT USE 5 Network Wiring Class A Style 7 Industry Inc Technologies Division Class B Style 4 Wiring No EOLR required 22 AWG min 12 AWG max 3300 feet max per pair NRCs or Unshielded pair with a minimum 3 twists per ft to Table 1 for NRC specifications Terminate shields at one end Power limited to NFPA 70 All wires supervised Ground fault detected at ohms or less Based XNET Connection NOT USE NOT USE NOT USE NOT USE NOT USE NOT USE NOT USE NRC NRC SLOT OF CC 5 SLOT OF CC 5 SLOT OF CC 5 NOT USE NOT USE NOT USE 6 Class B Style 4 Network Wiring Canada ULC S524 requires that all interconnecting data communications links for be wired DCLC style 7 except for dedicated network communication to the FN2006 FN2007 Installation Instructions P N A6V10315048 for wiring and connections Installation of the fiber modules in the XLS Desigo Fire Safety